Viatron AA800EZe Manual de usuario descargar pdf (Pagina 25)

AA800EZe rev.04

AA800EZe

Zone Status5.5.

5.5.1. Bypass / Activate

The Agri-Alert only monitors alarms in ac-

tive zones (the pilot light of an active zone

is steady green when there is no alarm or is

red if there is an alarm).

The system can also stop the alarm monitor-

ing temporarily in chosen zones. To disable

the alarm detection in a zone, set the zone

status to “bypassed” (the pilot light of a

bypassed zone is amber). Only active zones

can be bypassed.

If the pilot light of a zone is off, it either

means the zone has not been activated after

having been initialized or it has not been

initialized at all. Refer to section 3.7.8 to

activate a zone for the first time or to section

3.7 to create a new zone.

Select:1.

• Main Menu

• Activate / Bypass

• Bypass Zones

Select Zone to Bypass

1 2 3 4

Yes Yes Yes Yes

5 6 7 8

Yes Yes Yes No

Back

Modify

Press the zone number on the keypad to 2.

change its status. Select “Yes” to bypass a

zone or select “No” to reactivate it.

5.5.2. View/ Modify Zone Settings

You can display zone status information at

any time and/or modify certain zone param-

eters such as set points and recognition time

without having to reconfigure the zone.

Select:1.

• Main Menu

• View/Modify

• Zone Settings

Select Zone Number

Zone 1 Zone 2 Zone 3 Zone 4

Zone 5 Zone 6 Zone 7 Zone 8

Back

Enter

Use the numeric keypad to select the 2.

desired zone. The following parameters and

status informations are displayed:

Zone 1

Type Temp

State Activated

R e a d i n g 75.7 ° F

Low T° Set. 50.0°F

High T° Set. 90.0°F

Critical T°Set. 100.0°F

Calibration 0.0°F

Rec.Time 0:00:30(h:m:s)

Back

Zone 2

Temperature zone

Zone 2

Type Dry Contact

State By passed

Reading Open

Rec.Time 0:00:30(h:m:s)

Back

Zone 3

Dry contact zone

Type — This is the type of input used by the

zone: dry contact, temperature, instant bur-

glar or delayed burglar input. *Refer to section

3.7 to modify the type of input of a zone.

Status — This is the current status of the

selected zone. Here is a list of all possible

status:

Activated — The zone is activated and there

is no alarm. *Refer to section 5.5.1 to activate a

zone.

Alarmed — The zone is activated and there is

an alarm situation in it. *Refer to section 5.4 to

get information about the alarm situation.

Bypassed — Th e zo ne is ac ti va te d b u t te m p o -

rarily bypassed. The system does not monitor

this zone input. *Refer to section 5.5.1 to bypass

or to reactivate a zone.

Disabled — The zone has been initialized but

has never been activated. The system does

not monitor this zone input. *Refer to section

3.7.8 to activate a zone for the rst time.

Reading — This is the current reading of the

zone input. If you have selected a tempera-

ture zone, the Agri-Alert show the current

temperature reading of the sensor; if it is a

dry contact zone (burglar zone or not), the

system gives the current open/close state of

the contact.

Low / High (temperature zones only) — The

Ag ri - A ler t d is p la ys t he hi g h and low t em p e ra -

ture set points. To modify these limits, press

Enter and then use the numerical keyboard

to set them. *Refer to section 3.7.4 for further

information about temperature set points.

Critical (temperature zones only) — If an

outside temperature sensor is used, the

Agri-Alert displays the critical temperature

(absolute high temperature limit). To modify

it, press Enter and then use the numerical

keyboard to enter the desired value. *Refer

to section 3.7.4 for further information about the

critical temperature limit.

Calibration (temperature zones only) — The

calibration parameter allows adjusting the

reading of a temperature probe input: the

calibration value is added or removed from

all temperatures readings made in the se-

lected zone. If the zone’s probe needs to

be calibrated, press enter and then use the

numerical keyboard to set the calibration

value (use the +/- button once to enter a

negative value). By default, the calibration

value is set to 0.

Recognition Time — Determine during how

much time the alarm condition must be

maintained before it constitutes a valid alarm

situation.

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 31 32

Comentarios a estos manuales

Sin comentarios

Viatron AA800EZe Manual de usuario Pagina 25

Comentarios a estos manuales