Viatron AA800EZe Manual de usuario descargar pdf (Pagina 28)

AA800EZe rev.04

AA800EZe

9. TECHNICAL SPECIFICATIONS

TYPE: ................................... AA800EZe

Operating Temperature: .......... 32 to 104°F (0 to 40°C)

Indoor use only

Pollution Degree: .................. 2

Installation Category: ............ 2

Altitude: ............................... 7900 Ft. Max (2000 Meters Max)

Humidity: .............................. 95% max

Cleaning: .............................. Gentle soap and water

SUPP LY:

Transformer: ......................... 16.5 VAC, 40 VA, 50/60Hz

Battery: ................................ Rechargeable, 8.4V Ni-MH 2300 mAh

OUTPUTS:

Siren : .................................. 12VDC, 1A max

12VDC Output : .................... 500mA DC max

Relays 1-2: ............................ 24VDC or AC, 2A max

10. TROUBLESHOOTING GUIDE

System Troubles10.1.

Problem Solution

The "16V

disconnected"

or "16V

unstable" icon

is displayed

and electrical

power is OK.

Make sure the 12VDC output and siren do not

exceed the circuit capacity.

Check the wall transformer and wiring.

Use a voltmeter to check voltage at the 16VAC

input terminals (16VAC minimum).

If the problem persists, contact your dealer.

The "12V fail-

ure" or "12V

unstable" icon

is displayed.

Make sure the load connected to the 12VDC

does not exceed the circuit capacity.

Check the wiring of the 12VDC output.

If the problem persists, contact your dealer.

The "Low

battery" icon is

displayed and

electrical

power is OK.

Check the transformer and wiring.

Use a voltmeter to check voltage at the 16VAC

input

terminals (16VAC minimum).

Check the battery wiring.

Use a voltmeter to check voltage at the battery

(between 6 and 9 V).

Make sure the battery respects the electrical

specifications.

If the problem persists, contact your dealer.

The "Recharge

suspended"

icon is dis-

played.

That is not a problem. The system automatically

stops charging the battery when the battery's

temperature gets too high.

The "No bat-

tery” icon is

displayed.

Make sure a battery is connected to the control-

ler.

Problem Solution

The "Dis-

connected

line" icon is

displayed.

Make sure the entry line is plugged in the right

phone jack of the phone plug-in card.

Make sure the plug-in card is properly inserted in

the "PHONE CARD" connector.

If the problem persists, unplug the telephone

jack from the phone plug-in card and contact

you dealer.

The “Phone

Card Discon-

nected" icon is

displayed.

Make sure the plug-in card is properly inserted in

the "PHONE CARD" connector.

Check the phone line wiring.

If the problem persists, unplug the phone card

and contact your dealer.

The outside temperature

reading is replaced by

3 question marks.

Make sure the outdoor card is properly inserted

in the "OUTDOOR" connector.

Check the wiring of the outdoor probe.

If the problem persists, contact you dealer.

The SIREN does not

work.

Make sure the siren load does not exceed the

circuit capacity.

If no siren is connected to the siren terminals, a

resistor must be connected in its place (1.5kΩ,½

W) or you can disable the siren output as shown

in section 3.7.6 of this manual).

If the siren impedance is too high, add a 1,5K Ω,

½W resistor to the siren circuit, as close to the

siren as possible.

The siren wire or the siren may be defective.

If the problem persists, contact your dealer.

I plugged the battery

into the controller and it

doesn't start.

On first startup, the controller needs to be pow-

ered with the 16VAC wall transformer.

The system does not

detect

any probe.

Make sure the flat cable between the top and

the bottom board inside the enclosure is properly

connected.

Make sure the removable terminal plate is prop-

erly inserted on the bottom board.

Check the wiring of the zone inputs.

If the problem persists, contact your dealer.

The system shuts down

as soon as I unplug the

wall transformer.

Make sure the battery is correctly connected.

Let the system recharge the battery for about

3 hours and a half.

Make sure the load connected to the siren and

12VDC output do not exceed the circuit capac-

ity.

If the problem persists, contact your dealer.

The system refuses to

arm.

Make sure a burglar zone is programmed.

Make sure there is no active alarm in any burglar

zone.

If the problem persists, contact your dealer.

1 2 ... 23 24 25 26 27 28 29 30 31 32

Comentarios a estos manuales

Sin comentarios

Viatron AA800EZe Manual de usuario Pagina 28

Comentarios a estos manuales